Bulldog Security 721 Manuel d'instructions télécharger pdf

System Features ....................... 4

System Components ..................... 4

Required Tools ........................ 4

Technical Assistance................. 4-5

Before You Begin ...................... 5

Precautions........................... 6

Using your Test Probe.................. 6

Making Wiring Connections ............ 6-8

Locating & Making Connections ....... 8-12

Connecting the Wiring Harness ......... 13

Neutral Safety Switch................. 14

Operator Programming Instructions...... 15

How to use Your Remote Transmitter..... 16

Vehicle Anti-theft System Chart..... 17-20

FCC ID Notice ........................ 20

Important Functions................ 21-22

Warranty Validation .................. 21

Your Warranty ........................ 23

REMOTE STARTER • MODEL RS82I/RS85I/RS79

CONTENTS

Protected by one or more

of the following patents:

Patent #5,459,477Patent #5,612,670 

Patent #5,886,622Patent #5,677,664

Patent #5,942,988Patent #6,101,428 

Patent #6,452,772

Other patents pending.

ATTENTION:

We urge you to immediately place this card in your wallet.

PLEASE FILL OUT THIS FORM

AND MAIL IT IN TO REGISTER YOUR WARRANTY

Your Name ________________________________________

Address ________________________________________

________________________________________

Email Address _________________________________

Dealer Name ____________________________________

Address ________________________________________

________________________________________

Date of Purchase ___/___/___ Model # __________

Make/Model of Car ______________________________

Year of Car _____ V.I.N. # ____________________

Final Quality Check By _________________________

WARRANTY VALIDATION

Mail to: JBS Technologies

225 Technology Way • Steubenville, Ohio 43952

PROGRAMMING FUNCTIONS

FOR YOUR WALLET OR GLOVE BOX

Adding Additional Remotes

The hood must be open or the hood pin wire must be grounded. Then,

press and hold Button #1 on the working transmitter for ten (10)

seconds or until the ignition relay clicks or the check engine

light flashes once, release Button #1. Press and release any button

on the new remote control. The ignition relay will click or the

check engine light will flash three (3) times. Close the hood or

remove the hood pin wire from ground and try both remotes.

Tach/Tachless Option The brake must be depressed.

Press and hold Button #1 for 5 seconds or until the ignition relay

clicks or the check engine light flashes once. Release. Press and

release Button #1, the ignition relay clicks or the check engine

light flashes once. The unit is now programmed for Tachless Mode.

Press and release Button #2, the ignition relay clicks or the check

engine light flashes twice. The unit is now programmed for Tach

Mode. NOTE: The factory setting is Tachless Mode.

1 2 3 4 5 6 7 8 9 10

Résumé du contenu

Page 1 - WARRANTY VALIDATION

System Features ... 4System Components ... 4Required Tools ... 4Technical Assistance...

Page 2 - TECHNICAL ASSISTANCE

12 13Press the start button, if the unit receives a signal and your vehicle does not start and run you may have a factory anti-theft system. Refer to

Page 3 - PRECAUTIONS

4 21SYSTEM FEATURESTwo-Button Remotely start your car to run the heater or air Extended Range conditioning from an extended distance.Remote ControlT

Page 4 - USING YOUR TEST PROBE

20 5TECHNICAL ASSISTANCE (CONT.)BEFORE YOU BEGINIf your vehicle has an anti-theft system, you will need an additional module, Part #791.Congratulation

Page 5 - ANTI-THEFT SYSTEMS

6PRECAUTIONSMAKING CONNECTIONS1. Strip back two inches of insulation on the wire from the remote starter.Two Inches of Bare WireTo operate your test

Page 6 - UNDER DASH

18 76. Use electrical tape to wrap. Be sure to cover the wire about two inches on either side of the connection. First pull the wire that you have

Page 7

8 17LOCATING & MAKING CONNECTIONS4. Use electrical tape to wrap, be sure to cover about 2 inches on either side of connection. Secure with wire 

Page 8 - ADDING ADDITIONAL REMOTES:

16 9LOCATING & MAKING CONNECTIONSIGNITION WIRE(S) (WHITE) and (WHITE WITH RED STRIPE) (+12V in run, crank and sometimes accessory)Make all connect

Page 9 - Optional part #775 required

10 15LOCATING & MAKING CONNECTIONSfind a wire that shows (-) negative or ground when the parking lights are on, then switch the controller to the

Page 10 - CONNECTING THE 9-PIN HARNESS

14 11FACTORY ALARM SHUT DOWN WIRE (FASD) (-) (RED WITH BLACK STRIPE)If your vehicle is equipped with a factory alarm system (as most vehicles with a f